Alamo 2.5 hp with throttling governor, barn fresh, complete, except for splashguard and gas tank. Repair on mag trip bracket. Webster G mag. Should be easy to get started as everything is loose and free, $500; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Benz 5hp sideshaft engine, made in Czech Republic, portable engine on factory cart with cooling tank, muffler and wheel brakes, hit&miss governor, Bosch flipper magneto, a little over 7000 Benz engines were produced and this is the largest size they made and has 32” flywheels. Has been shown at the Oregon Steam-up in the past but hasn’t been run in several years, $9000; George Best nnn-nnn-nnnn (Beaverton OR) [link to photo]
Canadian Fairbanks 6 hp, Type H, Number C6442. Head has been welded, has water injection, accessory mag bracket, large pulley, and fuel pump. There is no splashguard. Needs to be assembled. It is in good shape, $1700; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Chain drive clutch assembly for engine, has number cast into clutch 62702 with 1& 7/16 keyed hole. I took off of 3hp Fairbanks Morse engine, $130; Daniel M. Thompson nnn-nnn-nnnn or xxxx@xxxx.xxx (Winnemucca NV)
DesJardan one cylinder engine. Between 5-6 hp. Has been sitting in the barn. Has compression. Please email or text for pics; Sam nnn-nnn-nnnn or xxxx@xxxx.xxx (Carlton OR)
Engines: IH 3-5 hp type LB, missing valve cover, sn 61220. Fairbanks Morse 2 hp D, self-oiling on homemade cart. Both engines ran good a year ago, $300 ea.; Jack Maki nnn-nnn-nnnn or xxxx@xxxx.xxx (Colville WA)
Fairbanks 1.5 hp Z, restored, no splashguard, runs, $500; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Fairbanks 3 hp Z, parts only. Good usable block, flywheels & crankshaft, best offer; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Fairbanks Morse 10 hp Z, 1924 hopper cooled engine. Starts easy, and runs great. No welds, rebuilt AB 33 kicker magneto, $4000 firm; Garland nnn-nnn-nnnn (Port Townsend WA)
Fairbanks Morse 3 hp Z, loose, needs magneto, $350; Garland nnn-nnn-nnnn (Port Townsend WA)
Fairbanks Morse D, older restoration, has belt pulley, always in shed after restored. Good runner, has not been used for a couple of years, $150; Daniel M. Thompson nnn-nnn-nnnn or xxxx@xxxx.xxx (Winnemucca NV)
Ford power plant 4 cylinder gas on wood skids with belt pulley. I used it to run a small sawmill, hasn't run in several years, always stored inside, $400; Jack Maki nnn-nnn-nnnn or xxxx@xxxx.xxx (Colville WA)
Frisco Standard shaft boat engine, disassembled, $5000; Charlie nnn-nnn-nnnn (Merced CA)
Fuller and Johnson 1.5 hp, head, valves, carb only, excellent shape, $80; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Gray 1 h.p., governor broken off and missing, all other parts move freely, $700; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Hercules IXB-3 engine, complete except for starter. Barn fresh. Hercules IXB-3 engine block w/head, & pan. Valves, pistons, crank in the block; Garland nnn-nnn-nnnn (Port Townsend WA)
Honda 9 hp engine, starts on first pull 98% of the time, $100; Lon Sisson nnn-nnn-nnnn or nnn-nnn-nnnn (Rohnert Park CA)
John Deere 3 hp, parts only. Good usable block, flywheels, crankshaft, piston, rod & cam gear, best offer; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Lorenz 4hp sideshaft engine, made in Czech Republic, portable engine on factory cart with cooling tank, muffler and wheel brakes, hit&miss governor, Bosch flipper magneto, this is a larger size than you normally see in this country and has 32” flywheels. Has been shown at the Oregon Steam-up in the past but hasn’t been run in several years, $9000; George Best nnn-nnn-nnnn (Beaverton OR) [link to photo]
McCormick Deering M hit & miss. On skids, loose, needs mag. Make offer. Vaughn drag saw. Complete with blade, turns over. Make offer; Chris nnn-nnn-nnnn or xxxx@xxxx.xxx (Camano Island WA)
Nelson brothers 5 hp throttle governor with water injection Stanley badge. This is a nice darn fresh engine that ran nice the last time I had it out. Complete with crank grad and muffler, $1100; Mike Cristler nnn-nnn-nnnn (Zamora CA)
Novo 1.5 hp, complete, restored, $750; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Novo single cylinder, 6 hp, rare throttle governed kerosene engine; Don Decker nnn-nnn-nnnn or xxxx@xxxx.xxx (Ridgecrest CA)
Stover 1.5 hp Type KE, head, valves & rocker arm only, $65; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Stover 18hp, throttle governed, portable, screen cooled, currently runs on sparkplug with buzz coil, but I have correct Webster ignitor and ignitor bracket for this engine. $10000 obo; George Best nnn-nnn-nnnn (Beaverton OR) [link to photo]
Stover 6 hp Type T, 1913, number X51115, restored. Hub has small crack, nice pulley, fuel pump, cast iron muffler, splashguard. Should be easy to get started as everything is loose and free, $1500; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)
Wade drag saw wood frame always stored inside hasn't run in several years nice, $350; Jack Maki nnn-nnn-nnnn or xxxx@xxxx.xxx (Colville WA)
Waterloo Boy 2.5 hp, number 72891, restored, complete, no gas tank. Should be easy to get running, $1600; Alan nnn-nnn-nnnn or xxxx@xxxx.xxx (Salem OR)