Boring bars for a 3 bar boring tool holder wanted. Sizes I need are 3/4 and 1-1/8" with square tool bit holes. Good US quality, please, Armstrong, Williams, etc; Robert Anderson nnn-nnn-nnnn (Kearny AZ)
Cultivator parts wanted: Oliver cultivators wanted for Fleetline 77, tubes, clamps, shanks, etc; Tom Winterrowd nnn-nnn-nnnn (Canby OR)
Cutter-bar lifting arm for a John Deere M-20 center mounted mower wanted. This is a cast iron part with the JD part number of AZ 3474H; Dick Deschamps nnn-nnn-nnnn or xxxx@xxxx.xxx (Bozeman MT)
Hay carrier trolley that runs on steel track wanted; Steve Zane nnn-nnn-nnnn (Paynes Cr. CA)
Old arbor press wanted, good US quality in working condition; Robert Anderson nnn-nnn-nnnn (Kearny AZ)
Old cross slide table wanted, to be used on a large drill press. Must have X and Y travel, good US quality; Robert Anderson nnn-nnn-nnnn (Kearny AZ)
Old mining equipment, small oil derrick, etc wanted; Larry Daniels nnn-nnn-nnnn (Phelan CA)
Old steel wheeled wagons/carts with saws, crushers pumps etc wanted; Larry Daniels nnn-nnn-nnnn (Phelan CA)
Plow shares & shins for John Deere Model 44 plow wanted: shares # B.C 217, need 3; shins #V 290 A, need 3; Philip S. Robustellini nnn-nnn-nnnn or cell nnn-nnn-nnnn or farmallf12 @att.net (Montague CA)
Tires wanted: 13x24 grader tires wanted; Charlie nnn-nnn-nnnn (Yakima WA)
Trailer wanted: Single axle low-boy trailer wanted; Charlie nnn-nnn-nnnn (Yakima WA)
Wanted, for a Sioux valve grinder-a holder for the diamond that dresses the main stone. Also
wanted the parts to dress the end of the rocker arms; Dale Longhurst nnn-nnn-nnnn (Delta UT)
Wanted: Early Scooters: Tote Goats, Cushmans, Valiants, Rose Ramblers, other makes & models; Buck nnn-nnn-nnnn or nnn-nnn-nnnn (Ellensburg WA)
Wanted: Consignments for 2014 Small Farmer's Journal Horsedrawn Auction & Swap Meet in Madras, Oregon HUGE EVENT April 24th - 27th, expands to fourth day featuring old tractors and stationary engines. CONSIGNMENTS being considered. Please send photo and information to xxxx@xxxx.xxx or SFJ PO Box 1627, Sisters, Oregon 97759; Lynn Miller nnn-nnn-nnnn or xxxx@xxxx.xxx (Sisters OR)
Wanted: Lathe driving dogs wanted. Bent tail type. Good US quality. Armstrong, Williams, etc, must be in usable condition. Sizes needed: 1-7/8", 2", 2-1/8", 2-3/8', 2-1/2", 2-7/8", 3", 3-1/4", 3-3/8", 3-1/2", 3-5/8", 3-3/4", 4". Old dogs were available in these sizes. Will take what is available. Also want outside jaws for a buck chuck, adjust true 3 jaw with a buck part # 4831. This is an 8-1/4" chuck. Need lathe chuck threaded back plates, 2-1/2" spindle, 6 threads per inch, 2-5/8" spindle, 6 threads per inch; Robert Anderson nnn-nnn-nnnn (Kearny AZ)