August 2018 - Engines & Parts For Sale

All Classified Ads

Alamo 2-1/2 hp hit and miss engine, complete engine, including Webster magneto and Webster bracket, all painted, but 70% apart, $500; Craig Mathews nnn-nnn-nnnn (Northridge CA)

Alpha De Laval 3 hp with rotary magneto. Runs great, barn fresh engine, complete less oiler, $700; Craig Mathews nnn-nnn-nnnn (Northridge CA)

Baker Monitor pump engine, with pump jack and Dempster pump setup on wagon for display, $1200; Richard Hanna nnn-nnn-nnnn (Rexford MT)

CH&E 5 hp on cart, $1400; Dennis Chaney nnn-nnn-nnnn (Dayton NV)

Challenge 2 hp, #3097, tulip hopper, runs, complete, on cart, $2200; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Climax engine by Climax Engine Company Iowa, big 6-cylinder gas engine, skid mount with radiator, dual ignition (magneto and distributor), dual carburetors, weighs approximately 5,000 lbs. engine is stuck. $1500 or some trades; Don Chappell nnn-nnn-nnnn (St. Helens OR)

Commercial 60 hp tank cooled engine made in Los Angeles, CA in 1915. Only known 60 hp Type C engine. It runs great and is easy to start with air. This impressively big engine is mounted on a 3-axle dedicated gooseneck trailer (CA license). Electric start gasoline air compressor for starting. A 6-inch United Pump made in Oakland is belted to the engine and can pump water for shows. Engine has been shown at several shows. Complete unit is $14000, will sell engine separate for $10000; Wilbur Reil nnn-nnn-nnnn (Davis CA)

Delaval 1-1/2 hp Type F, $600; Dennis Chaney nnn-nnn-nnnn (Dayton NV)

Economy E, 5 hp, nice paint and pinstriping on a nice homemade butcher block cart with rubber clad steel wheels, 8 inch flat belt pulley, Webster magneto, $850, photos available by email, can deliver to N. CA or S. CA in September; Ed 775-230-603 (Sparks NV)

Fairbanks Morse 10 hp Cannon barrel type on cart, $3500. Fairbanks Morse 2 hp Eclipse with hacksaw, $1400. Fairbanks Morse 1 hp Eclipse with water pump, $1200. Fairbanks Morse 1 hp Eclipse on skids, $950. Fairbanks Morse 1 hp headless type, $850. Fairbanks Morse 1-1/2 hp Model Z, $500; Dennis Chaney nnn-nnn-nnnn (Dayton NV)

Fairbanks Morse 1-1/2 hp, headless with Sumter magneto, complete, on cart, runs, $800; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Fairbanks Morse 20 hp Z tank cooled engine built in 1920. The impressive engine is on an iron wheel cart. Completely restored and painted. Runs great and has been shown at several shows. Few of the 20 hp engines still around, $7000; Wilbur Reil nnn-nnn-nnnn (Davis CA)

Fairbanks Morse 6 hp Z, has all parts, spins freely, previous owner had it running, but sat undercover since I got it, $650; Jon nnn-nnn-nnnn (Graham WA)

Fairbanks Morse D, $350; Dale Bybee nnn-nnn-nnnn (Acton CA)

Fairbanks Morse Z pump that was used for city of Mossyrock water system until 1948, $250; Dave Pearsall nnn-nnn-nnnn (Olympia WA)

Fairbanks Morse Z, 2 hp, self-oiling on cart, $400; Jack Maki nnn-nnn-nnnn or xxxx@xxxx.xxx (Colville WA)

Fairbanks Morse Z, 3 hp, SN 422739 (1919), original hot magneto, on skids, runs, $400. FM ZD (salt block style), on skids, runs, 1-1/2-2 hp, SN 770831 (1931) $175. FM Z, 6 hp, on heavy steel cart, original hot magneto, SN294083 (1918), $600. Pictures upon request; Dave Wirth nnn-nnn-nnnn or xxxx@xxxx.xxx (Walla Walla WA)

Fairbanks Morse, 3 hp, plug oscillator, older restoration by Jack Versteeg, $450; Warren Roberts nnn-nnn-nnnn or nnn-nnn-nnnn (Chehalis WA)

Fairbanks Morse, 6 hp, restored, nice runner, $1000; Dale Bybee nnn-nnn-nnnn (Acton CA)

Fairbanks, 1-1/2 hp, hopper condenser cooler, needs work, stuck, $225 obo; Larry Jacobson nnn-nnn-nnnn or nnn-nnn-nnnn (Salt Lake City UT)

Field Brundage 1-1/2 hp Wolverine, #6702, with Webster Tri Polar magneto, runs, on cart, complete, one flywheel needs new gib key, $850; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Foos 6 hp engine on original horse drawn cart. Has water hopper and rotary ignition. In excellent condition, approximately 1905. $13000; David Traver nnn-nnn-nnnn or xxxx@xxxx.xxx (Placerville CA)

Fuller and Johnson 2 hp, hopper cooled with Wico magneto and belt pulley, nice running engine, ran at Pottsville for 2 days last month, worked well, on steel tube base, $600, photos available by email, can deliver to N. CA or S. CA in September; Ed 775-230-603 (Sparks NV)

Fuller and Johnson farm pump engine, 1-1/2 hp, hit and miss, Model T coil, complete, runs great, comes with a metal cart, coil and battery. Also has a hand pump attached. Complete and in running condition, $2500; Dan Brockman nnn-nnn-nnnn (Chico CA)

Fuller and Johnson N 1-1/2 hp, early, #1717 with ignitor, runs, complete on cart, $750; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Fuller and Johnson N 3 hp, #81579, with ignitor, coil, battery, starts, complete, runs, on cart, $850; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Fuller and Johnson Pump engine, #115285, with pump jack and pump setup on cart for display, $1200; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Fuller and Johnson water pump powered by hit and miss engine. Draws a lot of attention at fairs, swap meets, and any place setup to draw people. Mounted on a cart with wheels so it’s easy to move. See it run www.youtube.com/watch?v=53NLJ1j-fRc, $2000; Dudley Mills nnn-nnn-nnnn or xxxx@xxxx.xxx (Campo CA)

Galloway 5 hp, 1910 round rod, complete, on original cart, not running, $1500; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Hercules drag saw, 1-3/4 hp, complete, hit and miss, Wico magneto. Restored to near perfect condition, runs and operates great. Have an extra saw blade, no broken parts, $2500; Dan Brockman nnn-nnn-nnnn (Chico CA)

Hercules E, 2 hp, hopper cooled engine on steel 4 wheel cart, recent paint and pinstriping, Webster magneto, $600, photos available by email, can deliver to N. CA or S. CA in September; Ed 775-230-603 (Sparks NV)

Ideal Model R, air cooled engine with belt driven fan, 2 hp?, nice brass Wico magneto, painted with some pinstriping, on nice steel homemade cart, $550, photos available by email, can deliver to N. CA or S. CA in September; Ed 775-230-603 (Sparks NV)

International engines, several off balers, combines etc. $100-$200. Rare stationary IHC engine grill, $70; Wendell Newman nnn-nnn-nnnn or xxxx@xxxx.xxx (Carson City NV)

International LB 3-5 hp, runs, on 2 wheel cart, $950; Richard Hanna nnn-nnn-nnnn (Rexford MT)

International M, 3 hp, older restoration, $800. 1-1/2 hp M, $700; Dale Bybee nnn-nnn-nnnn (Acton CA)

John Deere E, 1-1/2 hp engine. Complete but not running, $750; David Traver nnn-nnn-nnnn or xxxx@xxxx.xxx (Placerville CA)

John Deere E, 3 hp, $1050 obo; Larry Jacobson nnn-nnn-nnnn or nnn-nnn-nnnn (Salt Lake City UT)

John Deere E, 3 hp, ignitor is good, mag is hot, have not had it running, good compression, $550; Warren Roberts nnn-nnn-nnnn or nnn-nnn-nnnn (Chehalis WA)

John Smyth (Waterloo), 2-1/2 hp, original hot magneto, runs, on custom built cart, SN 36561, built around 1910, $900. Not run in a while. Photos on request; Dave Wirth nnn-nnn-nnnn or xxxx@xxxx.xxx (Walla Walla WA)

Light plant engine, 2-cylinder, skid mount, possibly Fairbanks, $150; Rob nnn-nnn-nnnn (Prineville OR)

Mogul, 1 hp, parts engine, $80. Unknown hopper/dry head $60; Dale Bybee nnn-nnn-nnnn (Acton CA)

Montgomery Wards 1-2 hp, 4-inch flat belt, #66279, rope pull start, from 1950s-1970s? runs, complete, $175; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Niagara engine, approximately 2 hp, missing carb and mag, otherwise looks complete, previous buyer did not follow through, $1700, photos available by email, can deliver to N. CA or S. CA in September; Ed 775-230-603 (Sparks NV)

Novo 3 hp with air compressor on cart, $1200; Dennis Chaney nnn-nnn-nnnn (Dayton NV)

Stover CT1 2 hp, #273583 with Wico mag, runs, complete on cart, $700; Richard Hanna nnn-nnn-nnnn (Rexford MT)

Stover CT-2 with Rex mixer, mixer has 5 brass tags, $800; Dale Bybee nnn-nnn-nnnn (Acton CA)

Stover vertical, MV-2 complete with gear box, $800; Dale Bybee nnn-nnn-nnnn (Acton CA)

Waterloo Boy 2-3/4 hp on cart, $1800; Dennis Chaney nnn-nnn-nnnn (Dayton NV)

Wisconsin 6-1/2 hp air cooled motor, rebuilt, $185; Dave Pearsall nnn-nnn-nnnn (Olympia WA)

Wisconsin V4 engine, ran when it was put in storage, $200 obo; Larry Jacobson nnn-nnn-nnnn or nnn-nnn-nnnn (Salt Lake City UT)

Wisconsin V4 engine, stuck, electric start, $90 obo; Larry Jacobson nnn-nnn-nnnn or nnn-nnn-nnnn (Salt Lake City UT)

Wisconsin V4 from hay baler with clutch and starter, $300 obo; Bob Arndt nnn-nnn-nnnn (Cromberg CA)

Witte, 5 hp, 1922 or 23, new rings, valves ground, bearings adjusted, aftermarket carburetor, Bosch magneto is stiff, new skids mounted on casters, $250; Warren Roberts nnn-nnn-nnnn or nnn-nnn-nnnn (Chehalis WA)