August 2019 - Engines & Parts For Sale

All Classified Ads

Challenge, 2 hp, SN 3097, on steel wheel cart, $2100; Rich nnn-nnn-nnnn (Rexford MT)

Cushman C, 1-1/2 hp, headless, #34820, on cart with cooling tank and water pump, ran several years ago, but been stored since, not stuck, complete, $350; Bill Ramsden nnn-nnn-nnnn (Minden NV)

Doak, 5 hp, $9500 obo; Danny Ponce nnn-nnn-nnnn (Los Angeles CA)

Drag saw parts, huge collection, includes 5 cylinders, 3 pairs of log dogs, sprockets and chains, trombone slides, clutch parts, flywheels, crankcases, bearings, grease cups, a brass throttle quadrant, fuel and water tanks for patterns, small hardware, and much more. Located in Renton Highlands, $100; Mike nnn-nnn-nnnn or xxxx@xxxx.xxx (Bellevue WA)

Economy S, 1-3/4 hp, complete original condition, runs good, $600; Mark Bruto nnn-nnn-nnnn (Placerville CA)

Emerson Brattingham, 2 hp, Webster magneto, original, $1100; Dennis King nnn-nnn-nnnn (Graham WA)

Engines: many Maytag and other odd air cooled engines; Ron Davis nnn-nnn-nnnn (Lakeside CA)

Entire collection for sale, well almost everything. Seager Old, 1-1/2 hp, nice barn fresh paint, no cart, $3000 obo. Hercules FW 1-3/4 hp, Webster magneto, new fuel tank, no cart, $600 obo. Alamo Project, 2-1/2 hp, Webster magneto, no cart, $350. International air-cooled Tom Thumb, complete, will run, no cart, $650 obo. New Way Little Giant, nice older restoration, on two-wheel cart, runs, make offer. Armstrong engine, 2-1/4 hp, on cart, $700. Easy washing machine engine, made for stationary use, external magneto, make offer. Sieverkropp engine, very nice, hard to find engine, approximately 1/2 hp, $2000. Lots of little goodies too. Additionally, vertical mill, 9-inch Logan lathe, all with attachments and tooling; Craig Mathews nnn-nnn-nnnn (Northridge CA)

Fairbanks Morse H, 4 hp, runner, $850; Dennis King nnn-nnn-nnnn (Graham WA)

Fairbanks Morse Z engines: 20 hp, fresh off the mind from AZ runs, $3700. 10 hp, on cart, 90% original paint, runs, $3400. 1-1/2 hp, headless hit and miss engine, complete, $400. 1-1/2 hp red line dish pan hit and miss engine, complete, $400; Ron Davis nnn-nnn-nnnn (Lakeside CA)

Fairbanks Morse Z, 10 hp, hopper cooled, type R rotary magneto, $1500;

Fairbanks Morse, 1-1/2 hp, headless, Sumter magneto, complete on cart, runs, $450; Rich nnn-nnn-nnnn (Rexford MT)

Field Brundage Wolverine, 1-1/2 hp, SN 6702, Webster magneto, on cart, runs, $850; Rich nnn-nnn-nnnn (Rexford MT)

Fuller and Johnson N, 3 hp, SN 81579, ignitor, coil, battery start, on cart, complete, runs, $850; Rich nnn-nnn-nnnn (Rexford MT)

Galloway 2-1/4 hp, 1914, hit and miss, runs great, but over all it is a mess, no magneto, etc. have the attachments for the magneto, but have converted to Model T coil, will have an extra Model T coil to go with it, $150; Dan Brockman nnn-nnn-nnnn speak loudly as hearing is going (Chico CA)

Idel 3 hp, vertical, hit and miss, complete, not stuck, $350; Ron Davis nnn-nnn-nnnn (Lakeside CA)

International M, 1-1/2 hp, complete, lots of original paint on wood skids, $450; Ron Davis nnn-nnn-nnnn (Lakeside CA)

John Deere engines, complete set, all on carts, all engines ran 4 years ago, $5000; Randy Wells nnn-nnn-nnnn or xxxx@xxxx.xxx (Vancouver WA)

John Deere hit and miss, 1-1/2 hp, 1926, runs good, easy start, just needs paint and decals; Jack nnn-nnn-nnnn (Port Orchard WA)

John Deere, 1-1/2 hp, on new skids with casters, fresh paint, valve grind and rings, $500; Warren Roberts nnn-nnn-nnnn (Chehalis WA)

LeRoi throttle governed, 4 hp, about 1924?, has magneto, upright model, starts easy and runs great, restored several years ago, nice and clean, all complete, you will like it, $300 with cart; Dan Brockman nnn-nnn-nnnn speak loudly as hearing is going (Chico CA)

Lister 4-1/4 hp, diesel, 1961, runs great, cold start design, has a starter to start it, starts easily, complete, replacement fuel tank, $250, as is, you pick up; Dan Brockman nnn-nnn-nnnn speak loudly as hearing is going (Chico CA)

Novo, 2 hp, runs with modified carburetor and external gas tank, on casters wheels, $450; Rich nnn-nnn-nnnn (Rexford MT)

Rider Erickson, 5-inch, running, propane, wood or coal burner, $7200; Dick Watson nnn-nnn-nnnn (Gridley CA)

Schmidt chill cylinder, 1-1/2 hp type B, rare, 1908, $3200 obo; Danny Ponce nnn-nnn-nnnn (Los Angeles CA)

Schmidt chill cylinder, 3 hp type H, SN X7597, 1907, buzz coil, $2500; Danny Ponce nnn-nnn-nnnn (Los Angeles CA)

Sparta, 6 hp, runner, $850; Dennis King nnn-nnn-nnnn (Graham WA)

Stover CT2, fresh Wico EK magneto, mounted on fresh skids with castors, $200; Warren Roberts nnn-nnn-nnnn (Chehalis WA)

Wisconsin AEN 1 cylinder, 8 hp, was running good, now won’t start, Wico magneto seems good, $25; Loren nnn-nnn-nnnn (Lakeport CA)

Witte headless, 6 hp, hit and miss, takes Model T coil and battery, will supply 2 Model T coils. No guard, non-original gas tank, excellent compression, ran when stored 5 years ago, one wheel wobbles a little, about 1914, had ran good and powerful, as is, pickup only, $250; Dan Brockman nnn-nnn-nnnn speak loudly as hearing is going (Chico CA)

Witte, 7 hp, buzz saw with 2 blades, SN 36820, complete with original cart, stored 25 plus years, $4500; Rich nnn-nnn-nnnn (Rexford MT)